Checkline TD-1-TE Instrukcja Użytkownika Pobierz pdf

-1-

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

1.1 Complete Kit

2.0 Overview of Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

3.0 Removing/Replacing Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

4.0 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

4.1 Setting Decimal Point

4.2 Setting the Low Alarm Limit

4.3 Setting the High Alarm Limit

4.4 Enabling & Disabling Electronic Damping

5.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

6.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07

6.1 Zero Adjustment

6.2 Gain Adjustment

6.3 Checking the Calibration

7.0 Analog Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

7.1 Changing Analog Output Type

7.2 Zero and Gain Adjustments

8.0 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8.1 TD-1-TE Specifications

8.2 Pin Assignments

8.3 On-Line Sensor Specifications

9.0 Warranty

TABLE OF CONTENTS

-16-

8.3 Online Sensor Specifications

Series TS (Models TS1,TSP, TSH, TSL,TSF, TSB1, TSB2)

Calibration: According to Electromatic factory procedure

Accuracy: For 10% to 100% of range: ± 1 % full scale

Remainder of

range and other

calibration material 3% full scale or better

Overload protection 100% of range

Measuring principle Strain gauge bridge

Measuring roller

deflection 0.5 mm, max.

Signal processing Analog

Output signal: 0 - 1 V DC (standard)

Damping (f

) Standard: 30 Hz (other values on request)

Temperature

coefficient: Gain: less than ± 0.01% full scale / °C

Temperature range 10 – 45 °C

Air humidity 85% RH, max.

Power supply Standard: 12 to 18 VDC (21 mA) (regulated)

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - TABLE OF CONTENTS

-1-1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 021.1 Complete Kit2.0 Overview of

Strona 2 - 8.0 TECHNICAL INFORMATION

ELECTROMATIC E Q U I P M E N T C O., I N C.600 Oakland Ave., Cedarhurst, NY 11516–U.S.A.TEL: 516-295-4300 • FAX: 516-295-4399 CHECK•LINE®INSTRUMENTST

Strona 3

-2-1.0 INTRODUCTIONPhoto of complete kit if availableThe TD-1-TE Tension Indicator accurately displays tension values calibrated in any unit of measur

Strona 4 - 4.0 SETUP

-3-2.0 OVERVIEW OF THE TD-1-TE INDICATOR3.0 REMOVING AND MOUNTING THE FRONT COVER1234256783910XXX.XX.XXXXX.XX01 = Digital display02 = Light emitting

Strona 5 - Damping enabled

-4-4.0 SETUP4.1 Setting the Decimal Point (Refer to the diagrams in Section 2.0)The decimal point is factory-set to the supplied sensor. If the indica

Strona 6 - 5.0 OPERATION

-5-3. Remove the front cover as described in Section 3.04. Loosen the retaining screw (11) at the bottom of the housing.5. Carefully slide out the PC

Strona 7 - 6.0 CALIBRATION

-6-5.0 OPERATION1. Install the sensor at the desired measuring location.2. Connect the TD-1-TE with the supplied sensor as described Section 8.2..Only

Strona 8

-7-6.0 CALIBRATIONAll tension meters are calibrated with standard material—such as polyamide-monofilament (PA)—according to the Electromatic factory p

Strona 9 - 9.0 WARRANTY

-8-6.1 Zero AdjustmentRequirements:• Decimal point set as described in Section 4.0.• Front cover removed as described in Section 3.0.• Sensor mounted

Strona 10 - WITH TE TENSION SENSORS

9.0 WARRANTYELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the original purchaser that this product is of merchantable quality and confir

Komentarze do niniejszej Instrukcji

Brak uwag

Checkline TD-1-TE Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Checkline TD-1-TE. Checkline TD-1-TE User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Checkline TD-1-TE